DRILL GRINDEREDG SERIES
Product Introduction
EDG-1226N(Ø12mm-Ø26mm)
EDG-213N(Ø2.5mm-Ø13mm)
| Model NO. | EDG-213N | Model NO. | EDG-1226N |
|---|---|---|---|
| Capacity | Ø2.5mm ~ Ø13mm | Capacity | Ø12mm ~ Ø26mm |
| Drill Angle | 90° ~ 135° | Drill Angle | 90° ~ 135° |
| Grinding Wheel | CBN#200(For Hss Drill) | Grinding Wheel | CBN#150(For Hss Drill) |
| Motor | 150W | Motor | 450W |
| Power Supply | AC110V / AC220V Single Phase (60Hz / 50Hz) |
Power Supply | AC110V / AC220V Single Phase (60Hz / 50Hz) |
| R.P.M. | 5500 R.P.M. | R.P.M. | 4500 R.P.M. |
| Weight | 8.5kg | Weight | 26kg |
| Standard Accessories | |
|---|---|
| ER collets Ø2mm ~ Ø13mm(12pcs) | ER collets Ø12mm ~ Ø26mm(15pcs) |
| CBN Wheel #200×1pc (For Hss drill) | CBN Wheel #150×1pc (For Hss drill) |
| Hexagon Wrench 4mm×1pc 5mm×1pc | Hexagon Wrench 4mm×1pc 6mm×1pc |
| Option Accessories | |||
|---|---|---|---|
| Order No. | Description | Order No. | Description |
| EDG-213N-1D | SDC Wheel #400 ( For Carbide drill ) Ø2mm ~ Ø13mm |
EDG-1226N-1D | SDC Wheel #200( For Carbide drill ) Ø12mm ~ Ø26mm |
| EDG-213N-2D | SDC Wheel #300(For Carbide drill) Ø10mm ~ Ø13mm |
||
| EDG-213N-1C | CBN Wheel #200( For HSS drill ) Ø2mm ~ Ø13mm |
EDG-1226N-1C | CBN Wheel #150( For HSS drill ) Ø12mm ~ Ø26mm |
| EDG-213N-2C | CBN Wheel #400 (For HSS drill under Ø5mm ) |
||
Collet Holder : bearing assembled
(More easy & convenient for tighting)
Set up the drill to the collet holder
Follow up the Steps 1, 2, 3, 4 for set up the drill to the collet holder. ( with out tighing) ***as shown on diagram #1
Set up the diameter of drill
- turn right the scale annulus to be "0" position.
- Adjust the scale to meet the diameter of the drill. ***as shown on diagram #2
Set up the drill to the grinding position
Insert the collet holder with drill and turn right, then tight the drill by collet holder for set up the grinding position.
***as shown on diagram #3
Attn: The scale annulus maybe not exact for the drill diameter, because of used drill or different model of drill any how, plase always check the center edge of drill must be parallel with the gap of "Collet Holder" ***as shown on the right diagram.
Grind the drill tip
- Turn on the power of the grinder.
- Insert the collet holder with drill and push to the grinding wheel slowly, then move left and right repeatedly to sharpen the drill until the grinding sound disappeared.
- Take out the collet holder with drill and change to the other side to grind agnin in same way as above mentioned ***as shown on diagram #4
Center Point Grinding Base adjusting
Adjust the center point grinding base to the suitable position. Turn right for bigger, turn left for smaller. ***as shown on diagram #5
Grind the center point of dirll
- Insert the collet holder with drill and push to the grinding wheel slowly, then move left and right repeatedly to grind the center point of drill until the grinding sound disappeared.
- Take out the collet holder with drill and change to the other side to grind again in same way as above mentioned. ***as shown on diagram #6
The center point suitable for hard steels . . .etc hard materials.
The center point suitable for general materials such as iron, general steel and brass . . .etc.
The center point suitable for soft materials such as copper, aluminum, plastic . . .etc.
***Plase clean the grinding chip often for avoid the chip scrape to the grinding base and keep using life.
This machine is guaranteed for one year under normal operating (expendable parts and wheels are exceptions)
